Firmware change log for WebControl™

WC32
12/7/2017 V4.02.22 Added Etekcity support to replace X10 RF
10/23/2017 V4.02.21 Add support to SET PWMF and PWMD frequency and duty
06/20/2017 V4.02.20 Changed sprintf, also changed ROM partition, update must save and reload all configuration and PLC code
05/15/2017 V4.02.19 Added support for 32 temp sensors
02/20/2017 V4.02.19 Extend hardware watchdog timer to a bigger value to avoid unintended reboot
10/10/2016 V4.02.18 Fixed ROTx bug
09/06/2016 V4.02.17 released with SPRINTF and STRCAT to format string for UM216 display
05/29/2016 V4.02.16 fixed a bug in RAM8H/L getting value, added UINT 16 bit AIP9 to AIP16 for storage
05/12/2016 V4.02.15 fixed a bug in IPINVx value reading
03/21/2016 V4.02.14 Added DS1307 present check so that when no DS1307 present, it will not display wrong time.

WC8
07/31/2018 V3.03.32 Removed VAR1-4 in each WEBSET call, to make sure ISY compatible
11/19/2017 V3.03.31 Added VAR1-4 in each WEBSET call, replaced X10 support with Etekcity RF
10/10/2016 V3.03.29 reduced email queue size, extended restart timer, set limit for set UROM value. fixed rotx bug
03/15/2016 V3.03.28 accommodate 10 WEBSET
02/25/2016 V3.02.27 allow user to set temp sensor config mode or temp sensor running mode
02/04/2016 V3.02.26 add checking for I2C logic
01/26/2016 V3.02.25 add parasite power support for 1-wire temp sensors
04/12/2015 V3.2.20 Added FWVERSION PLC operand
02/28/2015 V3.2.19 Enhanced Sendmail queue handling. Change GUI timeout to 120S.
10/20/2014 V3.2.18d5 Change watchdog timer value so that slower responds would not cause CPU restart
08/05/2014 V3.2.18d2 Enhanced DS18B20 from default 9 bit to 12 bit resolution
07/03/2014 V3.2.18a4 Added SREBOOT and SPIBYTE PLC operators
06/25/2014 V3.2.18a3 Removed DS2450 and SD2438 support
06/23/2014 V3.2.18a1 Removed DS2417 support
05/06/2014 V3.2.18a Added I2C support
04/07/2014 V3.2.18 Added DS2450 and DS2438 support
02/20/2014 V3.2.17g Enhanced 1-wire sensor communication
01/08/2014 V3.2.17f Added RAM1Bx. Fixed a TZ bug introduced in last version.
09/01/2013 V3.2.17e Added bootloader. Mapped RAM to four bytes or two 16bits, added LED and SETLED to PLC.
09/01/2013 V3.2.17e Added PROTECTED to PLC command, web GUI will not display PLC code with that keyword in.
07/26/2013 V3.2.17d Added bootloader support for 3.02.17d firmware.
04/17/2013 V3.2.17d Enabled getting server reply in the WEBSET command. Added DSTON operand
01/22/2013 V3.2.17a Fixed a display error showing two minus signs when VAR is a negative number.
01/22/2013 V3.2.17a Added ALLINS and ALLOUTS PLC IO identifiers for TTL inputs and outputs.
02/19/2013 V3.2.17 Added user set UROM value through api/seturom.cgi?uromid=x&value=y calls
02/19/2013 V3.2.17 Added ROTR and ROTL rotate PLC instructions
02/19/2013 V3.2.17 Allow WEBSET call to received server reply 32bit interger set WSRPLY IO identifier
02/19/2013 V3.2.17 Reduced allowed host list from 8 to four, added NTP server field allowing use different NTP server
01/22/2013 V3.2.16c Added trigonometry functions SIND, COSD, TAND.
01/22/2013 V3.2.16c Changed WEBSET to allow both auth and URL. Added trigonometry funcitons in PLC.
12/25/2012 V3.2.16b Fixed a compiler bug caused memory corruption in 3.02.16 and 3.02.16a. No feature change.
12/20/2012 V3.2.16a Allow in virtual host name field specify AUTHBASIC: with based64 encrypted username/password.
11/29/2012 V3.2.16 Change email to 8 different dest address. Add WEBSET feature to set value on another board.
09/12/2012 V3.2.15 Add fast pulse counter and frequency counter function, added ANDB, ORB, and XORB in PLC.
08/01/2012 V3.2.14 Fixed a potential bug in the non-blocking delay in certain PLC logic.
06/28/2012 V3.2.13A Changed hex to decimal conversion logic, now X10 changed from 0-F to 0-15.
04/20/2012 V3.2.13 Add TSDO for user adjust 1wire timing through web GUI
04/06/2012 V3.2.12 Change CTS to second since 2000/1/1. Fixed a MAC address txt string not terminate bug.
12/14/2011 V3.2.11 Change PLC instruction line size from 300 to 1000. Add UROM1-4 in general tab
11/23/2011 V3.2.10 Fixed a bug for temp reading between -0.9V to +0.9V.
10/18/2011 V3.2.09 Add DS2417 realtime clock support.
08/17/2011 V3.2.08 Add DS2450 so that four additional A/D channel is possible.
07/22/2011 V3.2.07 Add SetVAR http function for HW rev 2.2.2 board.
07/20/2011 V3.2.06 First PLC firmware for HW rev 2.2.2 board.
07/20/2011 HW Rev 2.2.2 board released. All firmware middle number changed to 2 to reflect the new hw.
07/17/2011 V3.1.06 Changed VAR to 32 bit and non-blocking delay to 30 bit number.
06/15/2011 V3.1.04 Support TSx (temp sensor status) being used in PLC logic
05/01/2011 V3.1.02 Support X10 devices through RF transmitter
07/05/2010 V3.0.00 PLC firmware released
01/25/2010 V2.3.06 Enabled the authentication code to allow email sent through servers require authentication.
01/25/2010 V2.3.06 Enabled the authentication code to allow email sent through servers require authentication.
01/18/2010 V2.3.05 Fixed a bug when using T1H in the BRE OFF field.
11/18/2009 V2.3.04 firmware released to require assign sensor ID for all temp sensors before reading.
05/08/2009 V2.3.03 firmware released calibrated the humidity based on HIH-4000 sensor.
04/16/2009 V2.3.02 firmware released adding ignore hour feature, changed the humidity calculating formular.
02/07/2009 V2.3.01 firmware released for restricting extension being handled by HTTPD.
02/02/2009 V2.3.00 firmware released to add support for DS18B20, to change temperature accuracy to 0.1 degree. Renamed TTL output from 0-7 to 1-8. Adding checkbox CGI support.
12/29/2008 V2.2.00 firmware released to change email port handling, add momentary output control, allow delay in BRE.
10/31/2008 V2.1.10 firmware released to fix a GUI processing bug.
10/08/2008 V2.1.09 firmware released to fix an email alert bug.
09/22/2008 V2.1.08 firmware released change the allowed host feature.
09/18/2008 V2.1.07 firmware released fixing security feature.
09/15/2008 V2.1.06 firmware released for erase flash incorrectly.
08/22/2008 V2.1.05 firmware released for CGI handling change and NTP handling change.
08/11/2008 V2.1.04 firmware released for internal discussion.
08/01/2008 V2.1.03 firmware released fixed a bug in AN6 handling.
07/20/2008 V2.1.02 firmware released to support timer programming in BRE.
07/20/2008 V2.0.2 hardware released to add protection for DS1822 and HIH-4000 sensors.
07/13/2008 V2.1.00 firmware released. Updated email function
06/27/2008 V2.0.02 firmware released. Changed some ADC logic for analog input to scale to 100%
06/25/2008 V2.0.01 firmware released
06/03/2008 V2.0.1 hardware released
04/07/2008 V2.0 hardware released
03/28/2008 V2.0 firmware released
01/30/2008 V1.5 hardware released
11/14/2007 V1.0 initial release